Honda CR-V - Antifreeze - Vehicle Specific
Your engine coolant, also called antifreeze, serves several purposes. First, it is circulated throughout the engine to the radiator to keep your engine at a stable operating temperature. Low coolant levels can lead to overheating, which can damage your engine. Second, antifreeze has a lower freezing point than water, which keeps it in a fluid state during cold weather. Coolant also keeps corrosion down inside the engine that may be caused by water. If you notice a coolant leak, it should be taken care of as soon as possible to avoid damage to your engine. You may notice your temperature gauge reading higher than usual, your heater may stop working, or you also notice steam under your hood. When you need coolant, visit O'Reilly Auto Parts for the right coolant for your vehicle. We carry a variety of coolant made for your car, truck, or SUV.Show More Show Less
Honda CR-V: Engine Coolant
Adding Engine Coolant
If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line.
Inspect the cooling system for leaks.
Always use Honda Long-life Antifreeze/ Coolant Type 2. This coolant is pre-mixed with 50 percent antifreeze and 50 percent distilled water. Never add straight antifreeze or plain water.
If Honda antifreeze/coolant is not available, you may use another major-brand non-silicate coolant as a temporary replacement. Make sure it is a high-quality coolant recommended for aluminum engines.
Continued use of any non-Honda coolant can result in corrosion, causing the cooling system to malfunction or fail. Have the cooling system flushed and refilled with Honda antifreeze/coolant as soon as possible.
If the reserve tank is completely empty, you should also check the coolant level in the radiator.
Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.
Always let the engine and radiator cool down before removing the radiator cap.
1. Make sure the engine and radiator are cool.
2. Relieve any pressure in the cooling system by turning the radiator cap counterclockwise, without pressing down.
3. Remove the radiator cap by pushing it down and turning it counterclockwise.
4. The coolant level should be up to the base of the filler neck. Add coolant if it is low.
Pour the coolant slowly and carefully so you do not spill any.
Clean up any spill immediately; it could damage components in the engine compartment.
5. Put the radiator cap back on, and tighten it fully.
6. Pour coolant into the reserve tank.
Fill it halfway between the MAX andMIN marks. Put the cap back on the reserve tank.
Do not add any rust inhibitors or other additives to your vehicle’s cooling system. They may not be compatible with the coolant or engine components.
Windshield WashersCheck the fluid level in the windshield washer reservoir at least monthly during normal use. Check the fluid level by removing the cap and looking at the level gauge. On Canadian models: T
Automatic Transmission FluidCheck the fluid level with the engine at normal operating temperature. 1. Park the vehicle on level ground. Start the engine, let it run until the radiator fan comes on, then shut off the en
Rear Differential Fluid4WD model only The rear differential should be drained and refilled with new fluid according to the maintenance messages shown on the information display. Have your dealer replace the rear
A/T Interlock SystemComponent Location Index DATA LINK CONNECTOR (DLC) SHIFT LOCK SOLENOID Shift Lock System Circuit Troubleshooting Test Replacement PARK PIN SWITCH Key Interlock System Circuit Troubleshooting Test Replacement STEERING LOCK ASSEMBLY KEY INTERLOCK SOLENOID Key Interlock System Circuit Tro
Valve, Spring, and Valve Seal RemovalSpecial Tools Required Valve spring compressor attachment PJA Identify the valves and valve springs as they are removed so that each item can be reinstalled in its original position. 1. Remove the cylinder head. 2. Using an appropriate-sized socket (A) and plastic mallet (B), lightly tap
© Copyright www.hcrv.net
- Hml clothing
- Gta v organization name
- <3 sister quotes funny
- Ogdensburg fire dept
- Allsource electrical technologies
News flash, Honda doesn't make anti-freeze. :D
You can use any non-silicate coolant meant for aluminium engines. Go to your local auto parts store, they'll show you which ones they have.
The most important thing is to thoroughly flush your cooling system first to make sure there is no trace of the previous coolant. Incompatible coolants can cause deposits inside your cooling system.
Given the age of the vehicle, I recommend that after you drain your cooling system, fill it up with a household cleaner that dissolves calcium, lime and rust deposits. Fill up the system completely with that stuff, run the engine to temperature, then turn on the blower to max heat and let it run a few minutes more, give the cleaner time to do it's thing. Then drain completely and fill the system back up with your favourite coolant.
answered May 31 '17 at
12k77 gold badges silver badges bronze badges
And here - at this very time - a fat photographer came up to me, unexpectedly. He stood behind. I felt his closeness, I felt aroused. After my behavior today, what could I talk to him about.
Honda coolant type crv 2003
Their eyes met. - Oh, Dr. Watson. How are you. I heard.Coolant location 2002 2003 2004 2005 2006 Honda CR-V
And where were you at that time, old goat. And how did you behave in court. I couldn't even give money to anyone. - The very fool is stuffed. - And I trampled your scent, moron, fat boar.
You will also like:
- Elf wiper blades
- Bandsaw butcher
- 81 arch street
- Valor bumper plates
- 1m1 shade conversion
- 17 days pregnant symptoms
- Birth info stuffed animal
- Fnaf toys mystery minis
- Mossy oak string silencers
- Watercolor house clipart
- Magic cards fat pack
- Morgan ward racing
- Omega craft ip
Felt this hardness, a little wet. - Wait. - Alexey was distracted, - It is necessary to do the necessary hygiene. - What. - I did not understand.